Osmo Country Colour Signal Red 5ml 2311
£1.30
Osmo Country Colour Signal Red 5ml 2311
Osmo Country Colour Signal Red 5ml 2311S
COLOURFUL DIVERSITY
- Extremely weather and UV resistant
- Very water and dirt resistant
- Reduces wood swelling and shrinkage
- Natural wood grain is hidden
- Microporous, breathable finish which does not crack, peel or flake
- No sanding necessary for future applications
2101 WHITE
- 2203 LIGHT OCHRE
- 2204 IVORY
- 2205 SUNFLOWER YELLOW
- 2308 NORDIC RED
- 2310 CEDAR/REDWOOD
- 2311 SIGNAL RED
- 2404 FIR GREEN
- 2501 LABRADOR BLUE
- 2506 ROYAL BLUE
- 2507 DOVE BLUE
- 2606 MEDIUM BROWN
- 2607 DARK BROWN
- 2703 CHARCOAL
- 2704 DUSK GREY
- 2708 PEBBLE GREY
- 2716 ANTHRACITE GREY
- 2735 LIGHT GREY
- 2742 TRAFFIC GREY
FINISHES
Opaque White, Light Ochre, Ivory, Sunflower Yellow, Nordic Red, Cedar/Redwood, Signal Red, Fir Green, Labrador Blue, Royal Blue, Dove Blue, Medium Brown, Dark Brown, Charcoal, Dusk Grey, Pebble Grey, Anthracite Grey, Light Grey, Traffic Grey
APPLICATION TOOL
Osmo Flat Brush or Osmo Microfibre Roller
RECOMMENDED USE
Exterior wood surfaces
RECOAT
One coat, when signs of wear become visible
SIZES
5ml, 125ml, 750ml, 2.5L
DRY TIME
10-12 hours
CLEAN UP
Osmo Brush Cleaner
COVERAGE
26m²/L with one coat
COATS
2 coats
CARE
Osmo Spray Cleaner (Exterior)
SURFACE PREPARATION
Wood surface must be clean, dry and frost-free (moisture content max. 20%).
Osmo Country Colour is ready to use. Do not thin. Stir well before use.
If possible, please apply the first coat to all sides before installation.
Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed.
As a general rule, wear a dust mask during sanding works.
The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat.
METHOD OF APPLICATION
With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and spread well.
Allow to dry for approx. 10-12 hours under good ventilation.
After drying, apply a second coat – also thinly.
For renovation works, one coat applied to the clean and dry surface is usually sufficient.
NOTE
If surfaces in outdoor areas (e.g. windows, cladding) should have additional protection, apply one top coat of Osmo UV-Protection-Oil Clear (410 without film protection or 420 with film protection) after thoroughly drying. This protects against dirt contamination and extends the life of the finish. For Country Colour White 2101, please use Natural Oil Woodstain White 900.
Country Colour, which has been trusted for over decades, is also available in the colour of your choice.
Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones, as well as with biocidal film protection additives.
Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered.
Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating.
CARE
Regular Cleaning: Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush.
Occasional Maintenance: If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean.
Recoating: Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.