Osmo Natural Oil Woodstain Patina 5ml 905
£1.30
Osmo Natural Oil Woodstain Patina 5ml 905
Osmo Natural Oil Woodstain Patina 5ml 905S
INNOVATIVE AND DURABLE PROTECTION
- Base and top coat in one finish
- Fast drying
- Natural wood grain remains visible
- Extremely weather and UV resistant
- Very water and dirt resistant
- Resistant against algae, mould, mildew and fungal attack
- Reduces wood swelling and shrinkage
- Microporous, breathable finish which does not crack, peel or flake
- No sanding necessary for future applications
700 PINE - UV-Resistance
701 CLEAR, MATT - UV-Resistance None
702 LARCH - UV-Resistance
703 MAHOGANY - UV-Resistance
706 OAK - UV-Resistance
707 WALNUT - UV-Resistance
708 TEAK - UV-Resistance
710 STONE PINE - UV-Resistance
712 EBONY - UV-Resistance
727 ROSEWOOD - UV-Resistance
728 RED CEDAR - UV-Resistance
729 FIR GREEN - UV-Resistance
731 OREGON PINE - UV-Resistance
732 LIGHT OAK - UV-Resistance
900 WHITE - UV-Resistance
903 BASALT GREY - UV-Resistance
905 PATINA - UV-Resistance
906 PEARL GREY - UV-Resistance
907 QUARTZ GREY - UV-Resistance
FINISHES
Various colour (Satin), Clear (Matt)
APPLICATION TOOL
Osmo Flat Brush or Osmo Microfibre Roller
RECOMMENDED USE
Exterior wood surfaces
RECOAT
One coat, when signs of wear become visible
SIZES
5ml, 125ml, 750ml, 2.5L
DRYING TIME
First coat: 4-6 hours, Second coat: 12 hours
CLEAN UP
Osmo Brush Cleaner
COVERAGE
26m²/L with one coat
COATS
2 coats
CARE
Osmo Spray Cleaner (Exterior)
SURFACE PREPARATION
Wood surface must be clean, dry and frost-free (moisture content max. 20%).
Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use.
If possible, please apply the first coat to all sides before installation.
Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works.
The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat.
METHOD OF APPLICATION
With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well.
Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat.
For renovation works, one coat applied to the clean and dry surface is usually sufficient.
NOTE
Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other.
Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones.
Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone.
Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas.
The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided.
Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating.
CARE
Regular Cleaning: Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush.
Occasional Maintenance: If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean.
Recoating: Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.